A dryer that won't heat, takes three cycles to dry a single load, or shuts off before the cycle ends isn't just frustrating — it's costing you time and money with every load you run. And a dryer with a blocked vent or a burning smell isn't just an appliance problem — it's a fire risk that needs same-day attention.
Erika Appliance Repair serves Tigard, OR with fast, certified dryer repair for both gas and electric models across all major brands. Our local technicians arrive prepared, diagnose the fault accurately, and restore your dryer to full working order — in most cases the same day you call.
A dryer that won't heat, takes three cycles to dry a single load, or shuts off before the cycle ends isn't just frustrating — it's costing you time and money with every load you run. And a dryer with a blocked vent or a burning smell isn't just an appliance problem — it's a fire risk that needs same-day attention. Stop running your laundry through back-to-back cycles and stop putting off a repair that could become a safety issue.
A dryer that tumbles but produces no heat is the single most common dryer fault we repair across Tigard. The drum spins, the timer counts down, the cycle completes — but the clothes come out exactly as wet as they went in.
On electric dryers, a burned-out heating element is the most common cause — the element has either burned out entirely or developed a partial break that reduces heat output to zero. A blown thermal fuse is the second most common cause on electric dryers — the thermal fuse is a one-time safety device that blows when the dryer exceeds a safe temperature threshold and must be replaced rather than reset. A failed cycling thermostat is the third — stopping heat delivery entirely rather than cycling it.
On gas dryers, a weak or failed igniter is the most common cause of no heat — as igniters age, they draw increasing current without reaching the temperature required to open the gas valve and light the burner. Burned-out gas valve solenoid coils are the second most common gas dryer no-heat fault — the coils open the valve to allow gas flow when the igniter reaches temperature, and when they fail, no gas reaches the burner regardless of igniter function. We carry heating elements, thermal fuses, igniters, and valve coils for all major dryer brands in Tigard, OR.
The most common cause of a dryer drum not spinning in Tigard is a broken drive belt — the belt wraps around the drum and connects to the motor via an idler pulley, and when it breaks, the drum stops turning entirely. A failed idler pulley that's seized and lost belt tension produces the same symptom — the motor runs but the drum doesn't turn because the belt has gone slack. A seized or failed drive motor is the third cause — producing a dryer that attempts to start but can't rotate the drum due to motor failure.
Belt replacement is one of the most frequently performed dryer repairs in Tigard, OR. We carry drive belts and idler pulleys for all major dryer brands in Tigard.
Lint accumulation in the exhaust vent is the leading cause of extended drying times in Tigard dryers. A vent that's partially blocked with lint restricts the volume of moist air the dryer can exhaust per minute — leaving clothes damp at the end of every cycle and forcing the heating system to run continuously rather than cycling efficiently. A crushed or kinked duct run, a stuck exhaust vent flapper, or a damaged blower wheel produces the same restricted airflow symptom without visible lint blockage. A failing cycling thermostat that's not maintaining adequate heat output produces extended drying times without the airflow restriction.
We inspect and clear the full exhaust path — from the lint trap housing through the duct run to the exterior vent flapper — on every dryer repair visit in Tigard, OR. A dryer repair that doesn't include a vent inspection isn't a complete dryer repair.
The most common cause of a dryer shutting off mid-cycle in Tigard is a blocked exhaust vent forcing internal temperatures above safe thresholds and triggering the high-limit thermostat or thermal cutout. A failing cycling thermostat that's triggering at normal operating temperatures — due to calibration drift or partial failure — produces the same mid-cycle shutdown without a vent blockage. A moisture sensor that's coated with fabric softener residue reads clothes as dry before they are and signals the control board to end the cycle prematurely — producing a consistent early cycle termination that's often mistaken for a control board fault.
We diagnose mid-cycle shutdown faults systematically — testing the vent, the thermostats, and the moisture sensor in the correct diagnostic sequence before recommending any component replacement in Tigard, OR.
Thumping or squealing during the drum rotation points to worn drum support rollers — the rollers hold the drum in position and allow it to spin smoothly, and as their bearings wear, they produce progressive noise that escalates to a thumping or squealing audible throughout the laundry area. Grinding or scraping sounds point to worn drum glides or a damaged front drum bearing — components that support the front edge of the drum and wear gradually under the drum's weight. Squealing during the spin cycle specifically points to a failing drive belt that's beginning to fray or an idler pulley bearing that's starting to seize. Rattling from inside the drum points to a loose drum baffle or a broken drum fin. Rattling from beneath the dryer points to a loose drain pan, a vibrating component mounting, or a failing blower wheel.
We diagnose noise faults by sound type and operational correlation before disassembly — narrowing the diagnosis significantly before we open the machine in Tigard.
The most common cause of a dryer not starting in Tigard, OR is a failed door switch — the door switch signals the control board that the door is closed and safe to operate, and when it fails, the dryer won't start regardless of the door position. A blown thermal fuse cutting power to the control board is the second most common cause. A failed start switch or start relay is the third. A control board fault causing complete loss of function is the fourth — distinguishable from the other causes through systematic electrical testing.
We test the door switch, thermal fuse, and start circuit before assessing the control board on every no-start dryer diagnosis in Tigard — because the simplest and least expensive cause is always the correct starting point.
The most common cause of dryer overheating in Tigard, OR is a blocked exhaust vent — when moist, hot air can't exit the dryer efficiently, internal temperatures climb rapidly beyond normal operating range. A cycling thermostat that's failed in the always-on position — leaving the heating element energized continuously rather than cycling — produces overheating without any airflow restriction. A failed high-limit thermostat that's been replaced without addressing the underlying vent or thermostat fault recurs quickly — we always identify the root cause of overheating rather than just replacing the safety device that tripped.
A dryer overheating with a blocked or restricted vent is one of the leading causes of residential dryer fires in Tigard. If your dryer is running excessively hot, take it out of service and call Erika Appliance Repair for same-day service in Tigard, OR.
Common dryer error codes we resolve in Tigard, OR include LG's D80, D90, and D95 vent blockage codes indicating progressively severe airflow restriction, Samsung's HE heating error and FE fan error codes, Whirlpool's F codes indicating specific system faults, and Bosch's error codes specific to their ventless condenser and heat pump systems. We interpret error codes as diagnostic starting points — confirming the specific component fault through hands-on testing rather than replacing the component the code points to without independent verification in Tigard.
Vent check every visit · Gas & electric · Warranty included
A burning smell from your dryer during operation is not a symptom to monitor — it's a signal to stop using the dryer immediately and call for professional service. A burning smell indicates one of four specific conditions, all of which require same-day attention:
The most serious cause, indicating that lint accumulation in the vent has reached a temperature at which it begins to char or ignite. This is the early stage of a dryer fire. Disconnect power to the dryer immediately and call Erika Appliance Repair in Tigard, OR.
The motor insulation or motor housing is burning under excessive thermal load. An overheating motor can damage surrounding components and create an electrical fire risk inside the dryer cabinet.
A belt that's beginning to fray generates significant heat at the contact point, producing a burning rubber smell that's distinct from lint or electrical burning.
A burning wiring connection, a failed terminal block, or a component developing a short circuit inside the dryer cabinet. Electrical faults inside an appliance require immediate professional inspection — do not restart the dryer.
A dryer requiring two or more cycles to dry what previously dried in one is a symptom that most Tigard homeowners tolerate for too long — accepting the extended drying time as a normal gradual decline rather than recognizing it as the airflow restriction warning sign it almost always is.
A dryer that's taking multiple cycles to dry is almost certainly running with a partially blocked exhaust vent. The lint accumulation restricting airflow is building toward the level at which overheating and vent ignition become real risks. Extended drying times are not a minor inconvenience to be managed with additional cycles — they are a warning that the dryer is operating in a condition that poses a fire risk if left unaddressed.
Lint is highly combustible — it's essentially loose, dry fiber with an enormous surface area relative to its mass, which makes it ignite easily and burn rapidly. Every load of laundry deposits lint in the dryer's exhaust system — some is captured by the lint trap, but a significant portion passes through and accumulates in the duct run, the vent connection, and the exterior vent cover over time.
As lint accumulates, it restricts airflow. As airflow restricts, exhaust temperatures rise. As exhaust temperatures rise, the accumulated lint eventually reaches its ignition temperature — and a dryer fire starts in the vent rather than inside the appliance. Dryer fires in Tigard homes are among the most common causes of residential appliance fires — and the vast majority are caused by lint accumulation in inadequately maintained exhaust systems.
Erika Appliance Repair includes a vent inspection as a standard component of every dryer repair visit in Tigard — not as an added service. Our technicians check: the lint trap and lint trap housing including the housing walls and screen frame; the transition duct from the dryer to the wall for kinks, crushing, disconnection, or lint accumulation; the exhaust duct run through the wall or floor by assessing airflow output at the exterior vent; and the exterior vent cover confirming the flapper opens fully during operation and isn't stuck, partially blocked, or damaged.
We report the findings of the vent inspection to every Tigard, OR customer before completing the repair — because a dryer repair that restores heat without addressing a vent restriction doesn't fully resolve the performance or safety issue.
The gas dryer igniter is the most commonly replaced component on gas dryers in Tigard, OR. As igniters age through normal use, their resistance increases and their heat output decreases — eventually reaching a point where they draw current and glow without reaching the temperature required to open the gas safety valve. The result is a gas dryer that starts, the igniter glows, but the gas valve never opens and the burner never lights.
We test igniter current draw before replacement — a strong igniter draw that's not opening the gas valve often indicates a valve coil fault rather than an igniter fault, and correct diagnosis prevents unnecessary igniter replacement when the actual fault is the coil. After replacement, we run a full heat cycle and confirm the burner is lighting reliably in Tigard.
Gas dryers have one or more solenoid coils on the gas valve that open the valve to allow gas to flow to the burner when the igniter reaches the correct temperature. When these coils fail — which they often do independently of the igniter — the valve won't open even when the igniter is glowing correctly. The result is identical to an igniter failure on the surface: the dryer starts, the igniter glows, but no heat is produced.
We test the solenoid coils with a multimeter to confirm resistance and continuity before replacement. Coil sets for all major gas dryer brands are stocked on our service vehicles for Tigard service calls, and most gas valve coil repairs are completed in a single visit in Tigard, OR.
The radiant flame sensor monitors the gas burner flame and signals the gas valve to stay open during the heating cycle. A failed flame sensor causes the burner to light briefly and then extinguish within seconds, producing a dryer that cycles on and off repeatedly without sustained heat output.
This intermittent burner behavior — lighting briefly, extinguishing, lighting again, extinguishing again — is the classic symptom of a failed flame sensor in Tigard gas dryers. We replace flame sensors across all major gas dryer brands in Tigard, OR, testing sustained burner operation after replacement to confirm the sensor is correctly maintaining the gas valve in the open position throughout the heating cycle.
Every gas dryer repair completed by Erika Appliance Repair in Tigard includes a post-repair safety verification — confirming the gas supply connection is leak-free at all accessible fittings, the burner is lighting reliably and producing a clean, stable flame, and the exhaust vent is clear and providing adequate airflow to support safe dryer operation. We use appropriate detection methods to verify gas connections after any repair involving gas system components in Tigard, OR.
The heating element is the most commonly replaced component in electric dryers across Tigard, OR. When it fails — either burning out completely or developing a partial break — heat output drops to zero. We always test element resistance to confirm failure before replacement rather than replacing based on visual inspection alone. We carry heating elements for all major electric dryer brands in Tigard and test heat output after replacement to confirm correct temperature output.
The thermal fuse is a one-time safety device that blows when the dryer's internal temperature exceeds a safe threshold. Once blown, it must be replaced — it cannot be reset. A blown thermal fuse is almost always a symptom of an underlying problem rather than a standalone fault. We always identify and address the root cause of thermal fuse failure — clearing the vent restriction or replacing the faulty thermostat responsible for the overtemperature condition — alongside the fuse replacement itself. Replacing the fuse without addressing the underlying cause in Tigard results in the replacement fuse blowing again, often within weeks.
The cycling thermostat regulates the air temperature inside the dryer drum by cycling the heating element on and off throughout the drying cycle. A failed cycling thermostat causes the dryer to run too hot — leaving the element on continuously rather than cycling it — or not heat at all — remaining in the off state regardless of drum temperature. We test thermostat resistance and opening temperature before replacement — confirming the thermostat is out of specification before recommending replacement in Tigard.
The control board manages all electric dryer functions — cycle selection, heat level, timer operation, moisture sensor response, and error detection. We diagnose control board faults accurately across all major electric dryer brands in Tigard, OR — distinguishing between a failed main control board and a failed user interface panel, which are different components requiring different repairs. We test all inputs to the board before concluding the board itself is the fault — because control board replacement is among the more expensive dryer repairs and should only be performed when the board is confirmed as the specific failure point in Tigard.
Gas, electric, ventless, heat pump, stackable · Same-day available
Vented dryers are the most common dryer type in Tigard homes — exhausting moist air from the drum through a duct to the exterior of the building. They develop the full range of faults we've described and are the most frequently serviced dryer type in our Tigard, OR operation. We carry parts for all major vented dryer brands and complete most vented dryer repairs in a single visit.
Ventless condenser dryers remove moisture by cooling the exhaust air until the moisture condenses — common in Tigard apartments and spaces without external venting. We service ventless condenser dryers from Bosch, LG, Samsung, Electrolux, Miele, and other brands across Tigard, OR. Condenser cleaning, heat exchanger faults, condensate pump failure, and control board issues are the most common ventless dryer repairs we perform in Tigard.
Heat pump dryers use a heat pump system to recycle heated air through the drum — achieving significantly lower energy consumption than both vented and condenser dryers. They're increasingly common in newer Tigard homes. We service heat pump dryers from LG, Bosch, Samsung, Electrolux, and others across Tigard, OR, handling heat pump compressor faults, refrigerant system issues, heat exchanger maintenance, and control board problems specific to heat pump drying technology.
Stackable washer-dryer configurations are common in Tigard apartments, condos, and homes with compact laundry spaces. We service the dryer component of all major stackable configurations across Tigard, OR with specific knowledge of the access techniques required to perform repairs efficiently within a stacked installation. Most stackable dryer repairs in Tigard are completed without requiring full disassembly of the laundry stack.
Combination washer-dryer units perform both washing and drying in a single drum — common in Tigard apartments and spaces without room for separate appliances. They develop faults in both the washing system and the drying system that may be independent or related through the shared control board. We service all combination washer-dryer brands and models in Tigard, OR, bringing specific knowledge of condensation drying systems to every combination unit dryer repair in Tigard.
Samsung DV series and WashTower combined units feature sensor dry technology and steam functions. Common Samsung dryer faults we repair in Tigard, OR include HE heating errors, FE fan errors, tS temperature sensor errors, and D80/D90/D95 vent blockage codes across the full Samsung dryer lineup in Tigard.
LG dryers feature TurboSteam, sensor dry, and EasyLoad door designs. Common LG dryer faults we resolve in Tigard, OR include D80, D90, and D95 vent blockage codes, heating element failures on electric models, gas igniter issues on gas models, and control board malfunctions across all LG dryer series in Tigard.
Whirlpool is one of the most common dryer brands in Tigard homes. We repair the full Whirlpool dryer lineup — Cabrio, Duet, and standard series — handling thermal fuse replacement, heating element failure, drum roller wear, belt replacement, cycling thermostat faults, and F-code error diagnosis across all configurations in Tigard, OR.
Maytag dryers are built for durability and heavy residential use. We service all Maytag dryer models across Tigard, OR including Bravos and Centennial series — handling heating element and igniter replacement, belt and roller wear, cycling thermostat faults, and control board issues across all Maytag dryer configurations in Tigard.
GE dryers are a staple in Tigard homes. We repair all GE dryer configurations — electric and gas, sensor dry and timed dry models — handling element failures, thermal fuse burnouts, drum component wear, and electronic control faults across the GE and GE Profile dryer lineup in Tigard, OR.
Bosch condenser and heat pump dryers are compact, ventless, and highly efficient — requiring familiarity with European-engineered condensation drying systems. We service all Bosch dryer models across Tigard, OR, handling condenser cleaning faults, heat exchanger issues, condensate pump failures, and control board diagnostics specific to Bosch's ventless drying technology in Tigard.
Erika Appliance Repair also repairs Frigidaire, Electrolux, Speed Queen, Amana, KitchenAid, Miele, Fisher & Paykel, Kenmore, and other dryer brands across Tigard. If your brand isn't listed, call us — if it dries clothes, we almost certainly service it in Tigard, OR.
Every technician dispatched by Erika Appliance Repair for dryer repair in Tigard, OR is a certified appliance specialist trained on both gas and electric dryer systems. Gas dryer repair requires specific knowledge of fuel delivery systems and safety protocols. Electric dryer repair on 240-volt systems requires specific electrical safety knowledge. Our technicians bring both to every dryer repair job in Tigard.
A broken dryer that's also a potential fire risk needs a technician today. Erika Appliance Repair maintains same-day availability across Tigard, OR through a local technician network and fast dispatch system — minimizing the time between your call and a technician at your door in Tigard.
Erika Appliance Repair includes a vent inspection as a standard component of every dryer repair visit in Tigard, OR — not as an added service or an upsell. We inspect the lint trap housing, transition duct, exhaust duct run, and exterior vent cover on every visit and report findings before completing the repair. A dryer repair that doesn't check the vent isn't a complete dryer repair in Tigard.
Every quote from Erika Appliance Repair is clear, itemized, and provided before any work begins. The final invoice matches the quote exactly. No hidden fees, no parts charges that weren't discussed, no additional labor time that wasn't agreed. If the repair doesn't make financial sense, we tell you before we start.
Every dryer repair completed by Erika Appliance Repair comes with a warranty covering both parts and labor. If the same fault recurs within the warranty period, we return and resolve it at no additional charge — no conditions, no service call fee.
Thermal fuse replacement, door switch replacement, idler pulley replacement, drum belt replacement, cycling thermostat replacement, moisture sensor cleaning or replacement
Heating element replacement, gas igniter and valve coil replacement, drum roller replacement, blower wheel replacement, control board replacement on mainstream brands
Motor replacement, control board replacement on premium models, heat pump dryer system repair
All quotes from Erika Appliance Repair are provided upfront and itemized before any work begins in Tigard, OR.
Repair makes sense when: the dryer is under 10 years old and the fault is isolated to a single component, the repair cost is under 50% of a comparable replacement dryer, or it's a premium model — heat pump, ventless, or steam — where replacement cost is significantly higher.
Consider replacement when: the dryer is over 12–15 years old with multiple prior repairs, multiple major components need attention simultaneously, or repair cost approaches the cost of a comparable new unit.
Call Erika Appliance Repair or use our online booking. Let us know your dryer brand, model, fuel type, and what you're experiencing — no heat, drum not spinning, loud noises, extended drying times, or error codes. Same-day appointments are available across Tigard, OR — call early for the best chance of a same-day slot in Tigard.
Our technician arrives within the scheduled window and performs a comprehensive dryer inspection — testing heat output, drum rotation, airflow, thermostat function, moisture sensors, door switch, blower wheel, and control board response. On gas dryers, we verify gas supply integrity and ignition system function. The vent inspection is performed on every visit — assessing the full exhaust path from the lint trap housing to the exterior vent flapper.
Once the fault is confirmed and the vent inspection is complete, you receive a clear itemized quote covering all repair work — parts and labor. No work begins without your explicit approval. No hidden fees. No charges for work you didn't authorize.
We complete the repair on-site using quality parts suited to your specific dryer. Our service vehicles are stocked with the most commonly needed dryer components for all major brands in Tigard — meaning most repairs are resolved in a single visit without waiting on parts delivery.
Before we leave, we run a complete performance test — verifying correct heat output, smooth drum rotation, and normal cycle completion. We confirm airflow through the exhaust system is within normal parameters and that the exterior vent flapper is opening correctly during operation. We don't consider a dryer repair complete in Tigard, OR until both the repair and the vent have been verified.
Our service area extends beyond Tigard city limits to cover surrounding communities across the Tigard, OR metropolitan area. Call us to confirm coverage for your specific address — in most cases we're already serving your area.
Our reputation in Tigard, OR is built on dryer repairs done correctly, vent inspections performed thoroughly, and customers who call us back when the next appliance needs attention. Fast response, accurate diagnosis, honest pricing, a vent check on every visit, and a warranty that means something — that's why Tigard homeowners choose Erika Appliance Repair for dryer repair.
A dryer that isn't working properly costs you time, energy, and money with every load — and a dryer that's overheating or running with a blocked vent is a safety risk that needs same-day attention. Erika Appliance Repair is ready to fix it fast — with certified local technicians, same-day availability across Tigard, OR, a vent check on every visit, honest upfront pricing, and repairs backed by a full warranty. Stop running your laundry through extra cycles. Call Erika Appliance Repair now and get your dryer back to full, safe working order in Tigard, OR today.